Master Installation Electrician

Master Installation Electrician





Operating Division:Transnet Pipelines


Employee Group:Permanent


Department:OPS & TEC, M&W, Electrical, ALR


Location:Alrode


Reporting To:Electrical Supervisor


Grade:H3


Reference:req5090











The closing date is on 29/06/2026. It is the responsibility of the applicant to ensure that HR has received the application before the closing date of the advertisement.



Position Purpose
The Master Installation Electrician is a person who has been registered as a Master Installation Electrician in terms of regulation 9 and who has been approved by the Chief Inspector for the verification and certification of the construction, testing and inspection of any electrical installation for efficient and effective custody, transfer and transport of petroleum products in liaison with Operations, Instrumentation and Mechanical departments in Transnet Pipelines.The Master Installation Electrician is responsible for electrical scheduling, inspection and to ensure safe working conditions.



Position Outputs
1) Managing of COC’s (Certificate of compliance)
a. Undertake periodic inspections and issuing COC’s as per National Codes and OSH Act
b. Conduct 2Y compulsory OHSact Hazardous area equipment inspections.
c. Maintain depot COC’s and compliance of Electrical Equipment housed in Hazardous areas.2) Give guidance and oversee Electrical Installations
3) Control the integrity of Equipment
•Ensure the correct application of the correct Electrical equipment in the Plant/operations4) PREVENTATIVE MAINTENANCE
• To perform preventative maintenance tasks on electrical equipment by detecting, repairing and reporting minor defects as well as reporting major defects thereby ensuring reliable equipment for the continuous operation of the pipeline e.g. 220V-3.3 Kv motors, control gear and trip protection equipment e.g Actuators5) DEFECT REPAIR
• Identify, analyse and repair defects on installed (live) equipment. Repair specific installed (live) equipment by performing
diagnostic tests to identify defects and effect repairs. Reading and understanding schematics and reports are essential e.g.
Mainline motor starter and trip protection, 380V panel starters and trip protection.6) BONDING
• Witness and install7) REMOVE AND REPLACE INSTALLED (LIVE) EQUIPMENT
•Removal and replacement of specific equipment by planning the complete installation, isolation and removal of the
equipment as well as preparing and installing the replacement, energising and testing the operations of the equipment e.g. Main motors, Actuators, lights, cranes, enclosures, isolators and stop/start stations.8) REFURBISHMENT AND MODIFICATION ELECTRICAL EQUIPMENT
Refurbishing equipment by disassembling the equipment, replacing defective parts, reassembling and testing the equipment
to the manufacturers specification e.g.
• Starters
• Actuators
• Certify all refurbished Equipment9) HIGH VOLTAGE EQUIPMENT
Obtaining authorisation and undertaking switching (A-Brown) and earthing on high voltage switchgear and equipment up to 132KV, issuing of work and test permits as well as undertaking maintenance of the above equipment. Also supervise
unathorised personnel in substations and HT yards
Work to a clearance of live high voltage equipment as per electrical HIGH VOLTAGE instructions10) SAFETY
• Attend Meetings
• Do Safety Inspections
• Use of safety equipment
• Ensure compliance of Equipment for flameproof safety and standards
• Assist with Job Observations and Supervision of personnel11) ADMIN
The effective control of administration duties which includes:-
• Reports (defect, inspection)
• Obtain and cancel hot work permits (Electrical)
• Job cards
• Operate SAP Modules (MM & IM)
• Maintain records, registers and COC’s as per applicable legislation
• Assist with internal electrical audits.
• Assist with Acting as an Electrical Supervisor as and when required.



Qualifications and Experience
Essential Requirements Trade Test Electrical (3 years) with 3 years Technical/Electrical on the Job experience. Must have adequate knowledge of all electrical equipment on Transnet Pipelines to be able to function on his/her own. The following courses must be passed with practical on the job experience during the three years’ experience in Transnet Pipelines. Obtain qualification and accreditation to qualify for a Master Installation Electrician Register at the Department of Labour as a Master Installation Electrician and complete 2 years on the Job Training and exposure and obtain final Accreditation. Computer literate SAP Course in Plant Maintenance (MM & IM Modules). Purchasing and Inventory, Word Excel, etc. High Voltage safety instructions (A-Brown) Thereafter a person has to get practical experience (training) on depots in the region until passed out. He/she has to attend a refresher course every two years and get tested and recertified every two years. NOSA (Safety) course Fire Fighting Oil spill course First Aid Level 2 Rotork actuator course on A-Range, IQT and IQ-Range Electrical motor course Transformer (HT) course Working in confined spaces Crossings and Cathodic Protection course ( Basic course) Theory: Operations Course: Thereafter a person has to get practical experience (training) on the depot where based until passes out on depot/manifold(s) Knowledge of testing instruments i.e. Megger, Thumper etc Code 8 driver’s licence Wireman’s licence Explosion Protection for Plant Maintenance Technicians(electrical and instrumentation)



Competencies
Computer Literate.
SAP_PM Literacy.
Knowledge of applicable tools and equipment.
Knowledge of Code of Practice 29.
Leadership skills.
Communication skills.
Ability to work as a team member.
Problem solving. – Root cause analysis
Interpersonal skills.
Basic knowledge and application of OHS Act.



Equity Statement
Preference will be given to suitably qualified Applicants who are members of the designated groups in line with the Employment Equity Plan and Targets of the Organisation/Operating Division.